[
    {
        "role": "user",
        "content": "can%20I%20remove%20a%20invevidual%20node%20from%20my%20deco%20be25%20network%20via%20the%20deco%20app%20on%20ios"
    },
    {
        "role": "assistant",
        "content": "Yes \u2014 you *can* remove an individual node (a \u201csatellite\u201d Deco unit) from your Deco BE25 mesh network using the Deco app on iOS. Below are the steps to follow, plus some caveats to be aware of.\n\n---\n\n### \u2705 How to Remove a Deco BE25 Node via the Deco App\n\n1. Open the **Deco app** on your iOS device and make sure you're logged in with the TP-Link ID that owns or controls the network.\n\n2. Go to the **Network** or **Network Map** tab. This typically shows all your Deco units (main and satellite) and their current status. ([service-provider.tp-link.com](https://service-provider.tp-link.com/nordic/faq/454/?utm_source=openai))\n\n3. Tap on the Deco unit (the specific node) you want to remove. This opens its device details \u2014 you\u2019ll see info like MAC address, IP, clients connected, etc. ([deco-mesh.net](https://deco-mesh.net/how-to-factory-reset-tp-link-deco-nodes/?utm_source=openai))\n\n4. Look for a menu icon (often three dots \u201c\u22ef\u201d in the top right), or a \u201cRemove\u201d or \u201cRemove Deco\u201d option. On many Deco models, you\u2019ll see \u201cReboot\u201d and \u201cRemove\u201d among available actions. ([static.tp-link.com](https://static.tp-link.com/upload/manual/2023/202301/20230111/1910013310_Deco%203.0_Deco%20App%20User%20Guide%20%28for%20DSL%20Decos%29_REV3.0.0.pdf?utm_source=openai))\n\n5. Tap **Remove**. The app will warn you that doing this will reset that Deco unit to factory settings and could reduce the network\u2019s Wi-Fi coverage. Confirm removal. ([digitalcitizen.life](https://www.digitalcitizen.life/factory-reset-tp-link-deco/?utm_source=openai))\n\n6. Wait a moment: the removed unit should disappear from the map. Its LEDs will change to show it\u2019s no longer part of the network (e.g. flashing patterns, depending on the model). After removing, you can re-configure it if needed. ([digitalcitizen.life](https://www.digitalcitizen.life/factory-reset-tp-link-deco/?utm_source=openai))\n\n---\n\n### \u26a0\ufe0f Things To Know & Common Issues\n\n- **Removing vs Deleting the whole network**: There\u2019s a difference. Removing a single node *only* disconnects that unit. Deleting the network resets *all* units to factory default. Be careful to only remove the one you intend to. ([reddit.com](https://www.reddit.com/r/TpLink/comments/1u86uci/deco_be25_advice_needed/?utm_source=openai))\n\n- **Must be connected to the network** to carry out removal. If the node you're trying to remove is offline or disconnected, you might not be able to remove it via the app. In those cases, a manual factory reset (using the reset button on the node) might be needed. ([reddit.com](https://www.reddit.com/r/TpLink/comments/1u86uci/deco_be25_advice_needed/?utm_source=openai))\n\n- After removal, the Deco unit becomes usable again, but as a fresh unit \u2014 you\u2019d have to set it up again from scratch if you want to re-add it. ([deco-mesh.net](https://deco-mesh.net/how-to-factory-reset-tp-link-deco-nodes/?utm_source=openai))\n\n---\n\nIf you want, I can walk you through step-by-step with screen images specific to your BE25 model, so it\u2019s easier to follow. Would you prefer that?"
    },
    {
        "role": "user",
        "content": "where%20abouts%20on%20the%20unit%20is%20tthe%20reset%20button%3F"
    },
    {
        "role": "assistant",
        "content": "On the **TP-Link Deco BE25**, the reset button is located in a small round hole on the *bottom* of the unit. To reset it, you use a sharp object (like a paperclip or pin) to press and hold it. ([tp-link.com](https://www.tp-link.com/au/document/27318/?utm_source=openai))\n\nHere\u2019s a summary of how it works:  \n- Press and hold for about **1 second**, then release.  \n- The LED on the unit will change from *pulsing yellow* to *solid yellow* to indicate the reset was successful. ([manualslib.com](https://www.manualslib.com/manual/3484325/Tp-Link-Deco-Be25.html?page=4&utm_source=openai))\n\nIf you want, I can send you a picture showing exactly where that hole is, so you can spot it visually."
    },
    {
        "role": "user",
        "content": "then%2C%20how%20do%20I%20add%20it%20to%20the%20network%20again%3F"
    },
    {
        "role": "assistant",
        "content": "Here\u2019s how you can add your Deco BE25 unit *back* into your existing mesh network using the iOS Deco app:\n\n---\n\n### \ud83d\udd27 Steps to Add the Deco BE25 Back into Your Network\n\n1. **Reset the Deco unit**  \n   Make sure it\u2019s been reset to factory defaults so it\u2019s ready for setup. After resetting, the LEDs should signal it\u2019s ready for setup. For BE25 units: Wait until the LED flashes blue ([static.tp-link.com](https://static.tp-link.com/upload/manual/2025/202503/20250326/1910013672_Deco%20BE25%28US%291.0_User%20Guide_REV1.0.0.pdf?utm_source=openai)).\n\n2. **Place it close to the main Deco**  \n   Especially during setup, keep the new node nearby the primary Deco unit so it can reliably find and pair with the network. If it\u2019s too far, it may not detect properly. ([service-provider.tp-link.com](https://service-provider.tp-link.com/faq/496/?utm_source=openai))\n\n3. **Open the Deco app on your iPhone/iPad**  \n   Make sure you\u2019re logged in with the owner account\u2014not a manager account\u2014as only owner accounts have permission to add new units. ([community.tp-link.com](https://community.tp-link.com/en/smart-home/forum/topic/853040?utm_source=openai))\n\n4. **Tap the plus (\u201c+\u201d) icon**  \n   - Navigate to the **Network** tab if needed.  \n   - Tap the **+** in the top corner, then select **\u201cAdd a Deco Unit.\u201d** ([tp-link.com](https://www.tp-link.com/support/faq/1590/?app=deco&utm_source=openai))\n\n5. **Follow app\u2019s instructions**  \n   The app will walk you through steps like powering on the Deco unit, selecting Wi-Fi settings, etc. Once the unit is discovered, finish setup as prompted. ([tp-link.com](https://www.tp-link.com/support/faq/1590/?app=deco&utm_source=openai))\n\n6. **Check the LED status**  \n   After joining the network:  \n   - It should go from solid blue (setup) to solid green (connected and functioning) ([tp-link.com](https://www.tp-link.com/au/document/27318/?utm_source=openai)).  \n   - If it shows a red light, it might be disconnected from the main Deco or there\u2019s some issue. ([tp-link.com](https://www.tp-link.com/au/document/27318/?utm_source=openai))\n\n---\n\n### \ud83d\udea7 Troubleshooting\n\nIf the app doesn\u2019t find the Deco unit:\n\n- Make sure the LED is flashing blue \u2014 that means it\u2019s in setup mode. If not, reset again. ([service-provider.tp-link.com](https://service-provider.tp-link.com/faq/496/?utm_source=openai))  \n- Keep the Deco close to the main one until it shows up in the app. After setup, you can relocate. ([tp-link.com](https://www.tp-link.com/support/faq/1590/?app=deco&utm_source=openai))  \n- Double-check that you\u2019re using the correct TP-Link ID (owner account). If you were using a manager account, it might not show the \u201cAdd Deco\u201d option. ([community.tp-link.com](https://community.tp-link.com/en/smart-home/forum/topic/853040?utm_source=openai))  \n\n---\n\nIf you like, I can send steps with screenshots specific to your version of the Deco app so it\u2019s easier to follow. Want me to do that?"
    }
]